Plasterboard comes in two thicknesses and we recommend you use the 12.5mm thickness for this job. The battens need to be as close to 400mm apart as possible allowing for the fact that you need the end of a plaster lath to fall on the centre of a batten so the next board can share the same batten.
Just so, How far apart should roof battens be?
Each product has different requirements, for example, batten spacing for (0.42BMT) corrugated metal roofing needs to be no more than 1100 mm apart, but batten spacing for 0.48BMT metal roofing can be up to 1600 mm apart.
Besides, Do you need noggins for 12.5 mm plasterboard? Well, firstly, you MUST have 12.5mm board. Secondly, you don’t need noggins unless the whole width or length of board will not get attached to joists. The 6 or 7 joists that the board is nailed/screwed to along the length is normal.
What is the normal spacing between studs? The general spacing for wall studs is 16 inches on center, but they can be 24 inches.
Subsequently, What is the maximum spacing for screw fixing plasterboard to a ceiling? Table 6: Acceptable fixing centres and fixings
Fixing | Location and spacing | Coating |
---|---|---|
Screw |
Ceilings: approximately 230mm centres (eight per two linear metres) Walls: approximately 300mm centres (five per linear metre) | Zinc electroplated or black phosphate (or to the board manufacturer’s recommendations) |
Table of Contents
How do you calculate roofing battens?
Deduct the length of the gutter overhang and the length of the nib from the length of the tile. For example, if the tile has a length of 16 inches, the overhang is 3 inches and the nib is 1 inch, the result is 12 because 16 – 3 – 1 = 12. This is the distance to the next batten.
How do you calculate roof battens?
The total length of battens you need for a roof depends on the number of rows of tiles.
- Measure the length of the eave, or the bottom edge that hangs out over the home, for each section of the roof. …
- Multiply the number of rows on each section by the length of the eave of that section.
How do you join roof battens?
Roof batten splicing
- Do not splice battens on girder trusses.
- Fix each batten to every lamination of every truss with minimum 2/nails.
- Adjacent battens should not be spliced in the same point.
- Not more than 1 in 3 battens to be spliced on any truss top chord.
Can you use 9.5 mm plasterboard on ceilings?
The most common plasterboard thickness is 9.5mm and 12.5mm. For ceilings is used 9.5mm thick plasterboard and for walls – 12.5mm.
How far apart should noggins be in stud wall?
If vertical timber planking is to be used for the cladding, position noggins at about 450mm (18 inch) vertical spacing.
What is a noggin loft?
Noggins, sometimes called bridging or blocking are timbers used all over the place during first fix/structural carpentry to strengthen and stiffen wall, floor and other timber structures.
Are studs always 16 inches apart?
Studs are boards that function as framing elements in your home, supporting the walls. You may wonder: How far apart are the studs in my home? They’re always spaced either 16 or 24 inches on center (measured from center to center) along the wall and run between the floor and ceiling.
Can studs be 8 apart?
Wall Length
Carpenters can only place studs precisely 16 inches apart if the length of the wall is exactly some multiple of 16 inches. This is often not the case, so at least one stud will often be much closer to the next one to make up for the difference.
Why are my studs not 16 inches apart?
You may be asking, “How far apart are studs?” The distance between studs varies slightly depending on the age of the home. Standard stud spacing is 16 inches on center and is rarely greater than 24 inches, even on center in older houses. Most electrical boxes for switches or outlets are attached to a stud on one side.
How far apart do you put screws in drywall?
Drywall screws should be placed 12 to 16 inches apart, but the distance can vary. Place screws eight inches apart on edges and ceiling edges, and no more than 12 inches apart on the ceiling field. Screws are the most secure and efficient way to hang drywall.
Is it better to nail or screw drywall?
While nails tend to be more flexible and hold up better against shear pressure—or lateral force—screws have much better grip and tensile strength, which ultimately keeps drywall from pulling away from the studs. When it comes to holding power, screws simply can’t be beaten.
Should I drywall the ceiling before the walls?
When hanging drywall, always hang the ceiling first. This is the hardest drywall to hang, so get a partner and go slow. Large cracks due to misaligned sheets are hard to repair because the extra mud required to fill them will constantly fall out and drop to the floor (or worse, down the back of your neck!).
How do you calculate batten spacing for roof tiles?
1 Measure distance between top of eaves batten and top of ridge batten. 2 Divide distance by maximum gauge of tile being used. 3 Round figure up to give number of courses up slope as a whole number. 4 Divide measured distance by number of courses to give batten gauge.
How do you calculate the number of battens?
Take your total wall length and divide that by the approximate spacing you would like between the battens. That number will be how many spaces you have on your wall. Add 1 to your number of spaces to get the number of battens on the wall.
How do you calculate roof tiles?
How to measure your roof. Take the roof width and multiply it by the slope height. This calculation will give you half the roof area, so then simply multiply by 2 to give you the area of both sides. You now have the area of your roof in square metres.